Produktai skirti pa 66 junginys (18)

Osmocem SCK Fiber-reinforced monocomponent cement mortar, based on hydraulic binders, superprogoline fillers, selected fine aggregates and crystallizing reagent agents, which favor the penetration of the compound into the support. Ideal for low-thickness protective coatings (4 to 10 mm), with high counterweight adhesion. The specific formulation makes this product ideal for coatings in aggressive environments in contact with chlorides and sulphates (sewage systems). Packaging: 25 kg bag UM: €/kg

Cortec VpCI® 382 Water-Based Urethane Topcoat. Protect against corrosion, abrasion, and weathering with this high-performance, water-based polyurethane topcoat. Featuring Cortec's VpCI® technology, it offers multi-metal corrosion protection, creating a molecular shield that safeguards both coated and nearby metal surfaces.VpCI® vapours reach hidden areas, eliminating the need for separate corrosion inhibitors. The durable finish resists damage and comes in various colours. Easy to apply and clean, this low-VOC, water-based coating is ideal for industrial equipment, structures, vehicles, and more.Enjoy long-lasting protection and a professional look with this cost-effective solution.

MP-0 Fett 400cc Kartusche Artikelnummer:1009570 HERSTELLER ART-NR.:249050

Methyl red is an organic compound that belongs to the family of azo dyes. It appears as a deep red powder, soluble in water and slightly soluble in ethanol. It is widely used as a pH indicator in acidic and basic solutions, as it changes from red in acid to yellow in alkaline. In addition to its use as an indicator, methyl red is used in the coloring of textiles, inks, cosmetics and as a dye in the food industry. However, its use in food applications is regulated due to concerns about its safety and potential toxicity in large quantities. CONTAINER:5kg. 25kg. 200kg. IBC

Repar Tix HG SB Thixotropic, structural, fibre reinforced cement mortar, with compensated shrinkage, with high intrinsic water tightness, and extraordinary physical and mechanical characteristics: adhesion, compression resistance, flexural strength, abrasion resistance, etc. Perfect for remediation of structural works and articles in degraded concrete and very high-performance coatings. Repar Tix HG SB, in addition to normal manual application techniques, it is a structural mortar specially formulated for applications with pumping/spray machines (wet spritz-beton technique). Particularly optimized parameters are: rheology, thixotropy and workability of the product, which allow spraying operations with reduced wear of the mechanical parts and little waste on the ground. Rheoplastic, thixotropic, structural, composite cement mortar, based on special cements and selected siliceous aggregates, reinforced with a balanced mixture of READYMESH polypropylene fibres and calcium metasilicate microfibres, added with specific agents and a high content of silica fume. After hardening, it provides very high performance in terms of intrinsic water tightness, resistance to washing and hydrolysing, mechanical strength, abrasion and cavitation, anti-carbonation, chemical-physical stability, resistance to harsh atmospheric agents and to leaching water. It has three-dimensional fibre-reinforcement, provides high hold; it is dimensionally stable (compensated shrinkage). The product can be supplied in mono-component or two-component version. The product, in the monocomponent version, is mixed with water (approx. 16% of the weight of the bag). In the two-component version, the product is mixed by adding the 4.5 kg of component B. The two-component version increases adhesion to the support and reduces free shrinkage to air, especially in the initial hardening phases and in particularly hot climates, without modifying the physical-mechanical characteristics of the end product. Repairs and protective coatings of hydraulic works (pipelines, dams, tunnels etc.), marine structures and artefacts in critical situations: aggressive chemical-physical agents, leaching water, marine atmosphere, etc. Specific for shotcrete interventions in galleries, tunnels, rock walls, irrigation and hydraulic channels, piles and micropiles, diaphragms, etc. Application surfaces should be clean, free of soiling, crumbling and non-adhering parts, dust, etc., conveniently saturated with water until they reach the condition "saturated with dry surface". An adequate roughening of the surfaces by scarifying, sandblasting etc. is always necessary in order to obtain the maximum adhesion values to the substrate. The optimal values are obtained with high pressure hydro-scarification. Bare the irons undergoing disruptive oxidation or deeply oxidized, removing the rust of the exposed irons (by sandblasting or abrasive brushes). The use of pumping/spraying machines specifically designed to be used with fibre-reinforced structural mortars is recommended. For the spraying of structural mortars such as Repar Tix HG SB, an effective and sometimes prolonged mixing of the product, which must take place upstream of the pumping circuit, is always recommended. For this reason, the use of “plaster sprayers” with volumetric water dosage is not recommended. Pour about 2/3 of the mixing water into the mixer, add Repar Tix HG SB and the remaining water; continue to mix until a homogeneous lump-free mixture is obtained. The mixing water should be about 16% of the weight of the bag. Addition of Bond HG to the mixing water, (approx. 0.5 litres per 25kg bag of product) in the single component version, allows further improvement in terms of adhesion, hold, impermeability, workability, modelling and deformation capacity. In the case of use of the product in the two-component version, pour component B (liquid) into the mixer, gradually adding component A (powder) and mixing until the lumps are completely eliminated. For high coating thicknesses, static requirements, monolithic requirements, etc., performed with Repar Tix HG SB, it is advisable to use suitable metal reinforcements (electro-welded mesh, cages, etc.), anchored to the support with Syntech Profix, GROUT MICROJ, Repar Tix G2. Approximately 18,5 kg/m² of Repar Tix HG SB for every centimetre of thickness to be implemented (approximately 1850 kg per cubic metre). Bag 25 kg - Pallet: 50 x (Bag 25 kg)

Osmocem N gray Cement compound for the preparation, with the sole addition of water, of a waterproofing osmotic coating that can create horizontal and vertical barriers, also suitable in conditions of negative hydrostatic thrust vis-à-vis water permeation in the buildings. Typical uses include waterproofing underground rooms, elevator compartments, garages, basements, tanks, etc. The action of the active components and of the adhesion promoters of Osmocem N, saturated by the reaction the support capillaries, forming a complex system of gel and stable crystals, which results in the best sealing, effective even in conditions of negative hydrostatic thrust, without hindering the breathability of the walls. Osmocem N is compatible for food substances: is certified as suitable for the containment of foodstuffs and drinking water (Certificate no. 02/2010 Laboratorio Analysis Service di Settimo di Pescantina - VR). Osmocem N waterproof test: • Resistance to positive hydraulic thrust, UNI EN 12390/8: water penetration depth with 5 bar pressure = 1-2 mm (*) • Impermeability to negative hydraulic thrust, UNI EN 12390/8 modified (concrete support a / c ratio 0.7): no passage of water with a pressure of 1.5 bar (*) concrete with penetration depth <= 20 mm are considered waterproof. Waterproofing rigid structures and masonry walls underground, buried or in any case subject to water permeation: lift wells, basements, tanks, pipes, tunnels, garages, bridges, reservoirs, areas containing food, etc. in conditions of positive and negative hydrostatic thrust provided they are sufficiently porous and absorbent and free from any waterproofing and / or water-repellent surface treatment, whether chemical (siloxanes, epoxies, polyurethanes, etc.) or natural (wax-up). Application surfaces should be clean, free of soiling, crumbling and non-adhering parts, dust, etc., water repellent treatments in general, etc. conveniently saturated with water until they reach the condition "saturated with dry surface". Pour about 2/3 of the mixing water into the mixer, add Osmocem N and the remaining water; continue to mix until a homogeneous lump-free mixture is obtained. The mixing water should be about 19-20% (for interventions in the form of a spatula) or 21-22% (for interventions using a brush with long bristles). After mixing is completed wait a few minutes before applying. If applied by brush, roll out two or more crossed coats. Although it is not a specific product for finishing thick coats, it can still be used for these purposes. In these cases, it is appropriate to use a fibreglass mesh Armaglass 160. Approximately 1.7 kg/m² of Osmocem N for each millimetre of thickness to be made. Packaging: 25 kg bag UM: €/kg

Grout 6 HP SFR Grout 6 HP SFR is a fibre-reinforced high-performance castable mortar, equipped with mechanical compressive and flexotraction resistance far superior to normal structural mortars. It is used for repairs, replenishments, strengthening concrete reinforcement and special works in FRC. The mix of special metal fibres (Readymesh MM-150) and synthetic fibres (Readymesh PM-060) is able to drastically reduce or even eliminate plastic-hygrometric shrinkage and the development of exceptional characteristics of ductility, fracture energy, resistance to shock and dynamic stress. With very low water-binder ratios, Grout 6 HP SFR makes it possible to achieve compacting and hyperfluid rheologies that favour the movement of the mortar and the perfect filling of reinforced sprays, even with narrow spaces between the bars. The microsilica with pozzolanic activity increases the cohesion of the mixture with typical anti-segregating and anti-run-off effect. The particular fineness of the hydraulic binders contained in the formula promotes adherence to the substrate and has an effect of enlarging the fibrous components. The fibre mix offers strong ductility, toughness and flexotraction resistance to the castings performed with Grout 6 HP SFR. With regard to the ANTICORROSIVE and PROTECTIVE FUNCTION ON THE REINFORCEMENT BARS, the main features of Grout 6 HP SFR are: • the mix of high-strength superfine binders, combined with very fine silicas with pozzolanic activities, to render the mortars intrinsically impermeable to water at the end of the hardening process; • The strongly alkaline pH (> 12) protects the reinforcement bars from triggering corrosion; • The negligible breathability of the carbon dioxide ensures hardened mortars with extremely prevalent anti-carbonation characteristics. Overall, these anticorrosive specificities render the classic treatment of reinforcement bar passivation, preparatory to the pouring of castable mortar UNNECESSARY, provided that not too much time passes between the white metal cleaning operations and the castings of pourable mortar, at the risk of new oxidative processes being triggered. Thus, only in the event that long exposure times are foreseen between the bar-cleaning operations and the pouring of castable mortar is it advisable to treat with passivating slurry (Repar Monosteel or Repar Steel), applied by brush and only on the reinforcing bars. On-site castings or pumping carried out for any kind of structural replenishment of reinforced concrete, seismic reinforcement and adjustment, increases in cross-sectional resistance of concrete structures and masonry, anchorages of large-scale machinery (especially in the presence of significant dynamic stresses), anchoring of port bollards, deep-drawing and reinforcement works, restoration of highly-stressed industrial flooring both from a static and dynamic perspective, restoration of degraded foundations on bridges and viaducts especially whereby necessitating rapid reopening to vehicle traffic, construction of structures designed with HPC (High Performance Concrete) needs. Application surfaces must be clean, free of dust, contamination, crumbling, inconsistencies, etc., and adequately saturated-surface-dry with water. An adequate roughening of the surfaces by scarifying, sandblasting etc. is always necessary in order to obtain the maximum adhesion values to the substrate. The optimal values are obtained with high pressure hydro-scarification. Bare the irons undergoing disruptive oxidation or deeply oxidized, removing the rust of the exposed irons (by sandblasting or abrasive brushes). Mix the entire content of a bag of Grout 6 HP SFR with effective vertical-axis mixers for at least 6 minutes, initially introducing a slightly reduced amount of water (9% = 2.25 litres/25 kilograms bag) compared to the required total water permitted (10%–12% = 2.5litres — 3.0 litres/25 kilogram bag) whilst mixing for at least 4 minutes. After this mixing time, evaluate the consistency of the mixture and, if necessary, gradually add in the last of the water until achieving the desired workability, without exceeding the limit of 12% (3.0 litres/25-kilogram bag), mixing at high RPM for at least another two minutes. For thick casting sections, it is advisable to add Ghiaietto 6.10 (consult the relevant technical data sheet or ask for more information on the appropriate dosage of Ghiaietto 6.10 from our technical service). Given the self-levelling properties of the product and its self-compacting capacity, paying due attention to the vibration phase is recommended. Excessive zeal in the vibration operation can worsen the aesthetic rendering of the end result. Do not use in the absence of suitable lateral containment. Ensure exposed surfaces are protected and wet-cured. Adopt casting procedures to ensure the absence of voids and discontinuities. Only pour the mortar from one part of the casting perimeter to avoid air pockets. Packaging: 25 kg bag UM: €/kg

Osmocem Quick Cement compound for instantaneously stopping water leaks in underground rooms or above-ground structures, even in the presence of negative thrust pressure. Based on rapid hardening and high resistance hydraulic binders of ultrafine quartz aggregates, shrinkage compensators, micronized hydrophobic products and specific additives for the regulation of rheology. It does not contain chlorides. Mixed with water it gives rise to a mixture of thixotropic plastic consistency, easily applied even vertically, which hardens in 30" - 60", adhering perfectly to the roughened support. Immediate stop of water infiltrations in building structures: basins, tanks, cellars, lift shafts, drains, underground masonry, etc. Examples of use: waterproof sealing of cracks and holes, waterproof repair before the addition of concrete, waterproofing systems made in combination with Flexseal 300 hydro-expansive sealant and waterproof mortars of the OSMOCEM line. Thoroughly clean the contact surfaces. In the case of cracks, discontinuities, cavities, etc. preliminarily prepare application sections countersinking towards the inside of the masonry, creating a "dovetail" shape (in order to facilitate the hydraulic sealing of the intervention). Remove any detached residual material from the prepared site, by means of pressure washing and jets of compressed air. Any interventions on temporarily dry surfaces require wetting of the support to saturation. Mix with water, if possible at a temperature not less than 20°C, no more than 250-300 cc per kg of product. The product reacts immediately and it is very quick, therefore mix from time to time the quantities of product strictly necessary and immediately applicable. Apply the product on site by hand exclusively and immediately after mixing the product with water while wearing protective rubber gloves. Press the mixed product firmly into the slot or hole and hold this pressure until the setting is complete (approx. 120 – 180 seconds). In case of multiple leaks, start the application of Osmocem Quick from the higher water leaks. Where necessary, in case of pressure infiltrations, proceed with the installation of drainage with a plastic tube, with small diameter, initially sealing sections adjacent to the drainage and then, once you stop the infiltration, sealing the drainage itself. Approximately 17 kg/m² of Osmocem Quick for every centimetre of thickness to be implemented (approximately 1700 kg per cubic metre). Packaging: 25 kg bag UM: €/kg

Grout 2 HP Grout 2 HP is a pourable, fiber-reinforced mortar, used for structural restoration operations, anchoring of steel bars and strands, reinforced micropiles, tie rods, and riveting. The formulation contains very fine high-strength cements, micro-silicas with pozzolanic activity, aggregates in a rational granulometric curve (0.1 ÷ 1.8 mm), and special antisegregative additives. The product is mixed with 11% - 12% of water, requiring vigorous and prolonged mechanical mixing. The special formulation of Grout 2 HP provides the castings with mechanical strength, fracture energy, exceptional durability, and very high chemical-physical resistance. Grout 2 HP has a workability time of about 60-90 minutes, after which the setting process is triggered, followed by progressive hardening. The plastic and hygrometric shrinkage is extremely low thanks to the presence of Readymesh PM-060 multifilament synthetic fibers, which provide volumetric stability. The performances that make Grout 2 HP unique are: • very high compressive mechanical strengths (> 90 MPa at 28 days), • very high mechanical resistance to bending-traction (> 12 MPa after 28 days), • excellent durability and resistance to chemical attacks. Grout 2 HP is used for structural restoration operations, anchoring of steel bars and strands, reinforced micropiles, tie rods, and riveting. It is particularly suitable for operations where high mechanical performance is required after short curing (compressive strength at 3 days > 60 MPa) and in operations carried out in severe exposure environments (XC - XS - XF), characterized by aggression from sulphates, chlorides, and nitrates. The material can also be used for repairs in anchoring areas subject to high stresses. The application surfaces must be clean, free of dirt, crumbly and incoherent parts, dust, etc., and suitably saturated with water until reaching the condition of "saturated with dry surface". Adequate roughening of the surfaces by scarifying, sandblasting, etc. is always necessary to obtain the maximum adhesion values to the substrate. The optimal values are obtained with high pressure hydro-scarification. Bare the irons undergoing disruptive oxidation or deeply oxidized, removing the rust of the exposed irons (by sandblasting or abrasive brushes). It is strongly recommended, for optimal performance of site operations, to use a vertical axis mixer with planetary movement or a double horizontal helicoid. The powder is mixed with drinking water to the extent of 11% - 12%, referring to the total weight of the mortar (about 2.75 liters per 25 kg bag) until a homogeneous mixture is obtained. Mixing time: about 4 minutes with a high efficiency mixer. The anchoring can be filled with a single screw pump, for mortars. Pumping must be carried out at a controlled speed to ensure a low working pressure. In case of restorations, the surface must be protected, after application, by polyethylene sheets or anti-evaporation treatments. Packaging: 25 kg bag Unit of Measure: €/kg

VPCI 309 is a vapour phase corrosion inhibitor based VCI powder suitable for long term continuous corrosion protection of ferrous metals in ‘hard to reach’ areas, void spaces, restricted areas, cavities, and awkward inner spaces. Cortec VPCI 309 utilizes a highly effective ‘dry method’ to guard metals within an enclosed area. The VPCI® technology essentially evaporates and is absorbed onto the metal surfaces that are exposed within the surrounding area or space. Effective when dealing with interior cavities for plant equipment, heavy machinery, etc. VPCI 309-SF is available as a silica-free specification, available made to order. VPCI 309 Key Features Nitrates, Phosphates, & Silica Free Provides continuous corrosion protection for up to 2 years Thin but robust monomolecular inhibitor layer Vapour Phase mechanism of action is highly effective targeting hard to reach surfaces No need to remove powder from protected items prior to shipment

Cor-Pak VpCI®-tabletten zijn een marktleidend alternatief voor traditionele VCI-emitters Ze presteren beter dan andere VCI-tablets en zijn ideaal voor gesloten of lastige ruimtes en kunnen ook gemakkelijk in flexibele verpakkingen door handmatig of geautomatiseerd proces. CorPak-tabletten gebruiken een zeer efficiënte 'droge roestpreventiemethode' om gevoelige metalen te beschermen tegen corrosie in een afgesloten ruimte. Cor-Pak-tabletten combineren gepatenteerde Cortec-bedrijven technologie voor corrosieremmers in de dampfase (VpCI) met een eenvoudig aan te brengen / af te geven tablet. Deze methode kan worden gebruikt op alle soorten metalen (ferro en non-ferro) om tot 24 maanden corrosie- en roestbescherming te bieden. Het werk van VPCI door zich te hechten aan de omringende metalen oppervlakken. De kleine, compacte tabletvorm maakt ze ideaal voor inbouwruimtes of gesloten binnenruimtes.

Cortec M-531: Shield Your Metals. Cortec M-531 is a potent, oil-soluble corrosion inhibitor safeguarding metal surfaces across diverse industrial sectors.This versatile product seamlessly integrates into lubricating oils, fuels, hydraulic fluids, and similar hydrocarbon blends, delivering robust protection against rust and oxidation. Engineered with a cutting-edge formulation of corrosion-inhibiting components, M-531 constructs a formidable barrier on metal surfaces, effectively repelling moisture, oxygen, and other corrosive threats.Its efficacy shines in both indoor and outdoor settings, making it a dependable choice for various applications. Key advantages include exceptional corrosion prevention, unparalleled versatility in fluid types, extended equipment lifespan, effortless application, and eco-friendly composition.

Cortec VpCI® 419 Heavy Duty Degreaser/Cleaner. Powerful, heavy-duty cleaner with VpCI® technology.Cuts through grease, oil, and grime. Protects metal from corrosion.Biodegradable, non-toxic, and non-flammable.Ideal for industrial, automotive, and marine use. Versatile application methods.Safe and effective.

Cortec VpCI® 380 Railcar Coating. Protect your railcars with Cortec VpCI® 380, a cutting-edge, water-based acrylic coating.This innovative solution offers superior corrosion protection, directly applied to metal without primer. Enjoy long-lasting durability against harsh weather, easy application, and an attractive finish.Ideal for railcars, trucks, and more. Protects ferrous and non-ferrous metals.Maintain your fleet's value with Cortec VpCI® 380.

Cortec VpCI® 427 Inhibitor - Revitalise Your Aluminium Components. Protect aluminium from corrosion with Cortec VpCI® 427.This versatile inhibitor uses VpCI® technology to create a molecular barrier against moisture, salt, and pollutants.Ideal for aerospace, automotive, marine, and industrial applications, it safeguards aluminium components during storage, shipment, or long-term use. Easy to apply by spraying, dipping, or fogging, Cortec VpCI® 427 is water-based, non-flammable, and environmentally friendly. Proven performance and industry certifications ensure reliable protection for your valuable aluminium assets.

Cortec VpCI® 322 is a concentrated, solvent-based oil safeguarding ferrous and non-ferrous metals from corrosion. Leveraging advanced VpCI® technology, it forms a thin, transparent film that protects against rust, even in hard-to-reach areas.This oil not only inhibits corrosion but also lubricates moving parts due to added anti-wear agents.Its low viscosity ensures easy application and penetration.Ideal for equipment, parts, and components during shipping, storage, or lay-up, VpCI® 322 safeguards a wide range of metals, including carbon steel, stainless steel, copper, brass, aluminium, and galvanised steel.

Cortec VpCI® 391 Water Based Temporary Coating. Safeguard your metal parts and equipment from corrosion with Cortec VpCI® 391.This innovative, water-based coating provides exceptional protection against rust, tarnish, and other forms of corrosion.Utilising Cortec's patented Vapor phase Corrosion Inhibitor (VpCI®) technology, it creates a transparent, protective barrier that shields metal surfaces during storage and transit. Easy to apply by spraying, brushing, or dipping, VpCI® 391 dries quickly to a non-tacky finish, allowing for immediate handling. Environmentally friendly and free of hazardous chemicals, this versatile coating protects a wide range of metals, including steel, aluminium, and copper.Ideal for machinery, tools, automotive components, and more, VpCI® 391 offers up to 2 years of indoor and 6 months of outdoor protection.Simply remove with water when ready for use.

VPCI 322 is een op olie gebaseerde, geconcentreerde corrosiebeschermingsoplossing. Cortec VPCI 322 presteert zowel binnen als buiten goed. Cortec VPCI-technologie wordt in deze formule gebruikt. Ze vormen een dunne, robuuste, enkellaagse film die zich hecht aan metalen oppervlakken en uitstekende contactcorrosie- en roestbescherming biedt. Dampfase-corrosieremmers (VPCI) worden gebruikt in de 322-formule. Dit biedt bescherming naast het fysieke barrière van de film zelf. Het VPCI-molecuul verdampt in wezen in de lucht boven de corrosieremmende olie. Deze VPCI-moleculen 'hechten' aan metalen oppervlakken en kunnen langdurige roestbescherming bieden. VPCI 322 kernpunten Biedt 'multi-metal' roestbescherming voor zowel ferro als non-ferro metalen Zonder barium, chromaten, fosfaatremmers en nitraat Hoog vlampunt Hoge thermische stabiliteitsformule. Contactcorrosie op lange termijn met Vapor Phase-technologie Gaat gemakkelijk door een filter van 5 micron